Expert Home Repairs & Waterproofing in Snohomish County, WA

This homes basement had been waterproofed from the exterior a while back. This had involved an exterior drain system that was installed about six feet down along their homes foundation. But this system had clogged. The company that had installed it said they could excavate around the home to reach the system and clear it out, but it would be costly, and would involve a lot of disruption to the homeowners landscaping. Looking for a new way to address waterproofing, the owners contacted John's Waterproofing. With over fifty years in the industry, and specializing in an interior waterproofing system, the owners were intrigued. We walked through our system and the cost, and landed on a repair plan. 

To begin we dug a trench along the basements interior perimeter. We then install gravel and our WaterGuard drain system along this. The system is all on the interior and we install check points periodically along it to ensure we can check and maintain the system as needed over the years. This collects the groundwater and has water from the foundation walls guided to it. The walls have BrightWall paneling installed along them, this material will not mold or rot, just safely guide water to be addressed. We also installed drainage for each window well that sat below-grade. Water travels along the new drain system to the lowest point of the space where it is pumped safely away from the foundation by a newly installed TripleSafe sump pump. A SaniDry dehumidifier was installed and this home can now enjoy a dry basement once more. And they can rest easy knowing we can easily maintain the system, ensuing it keeps working year after year. 

Under this home there was falling insulation and water damage. Mud was over the old vapor barrier and efflorescence along the foundation walls where water had been coming through. The homeowner didn't want to be breathing in this mess so they called up John's Waterproofing to learn how we could make their home dry and healthy.  We cleared the crawl space out, and began work on a full encapsulation. We dug a trench and installed a drainage system to collect and guide groundwater to the new SuperSump Plus which pumps the water away from the home. We then sealed the vents shut and spot treated a few places where mold had been showing up. Next we laid TerraBlock insulation along the crawl space floor and brought in the new vapor barrier. This is our CleanSpace, 20 Mil thick woven plastic that wraps under each wooden post, anchors and seals along the foundation walls and along each seam. We then installed a SaniDry dehumidifier and spray foam insulation along the walls. The final step was an Aspen air purifier in the living space to help this home be healthy! 

When the floors bounce in the home, some structural work can help. This homeowner called up John's Waterproofing for their free inspection and joined the design specialist under the home. We found one of the wooden beams was squishy, and most of the wooden posts were either rotting or floating above their footings. Some serious moisture issues were occurring, and had been occurring for a prolonged amount of time. To begin we replaced the wooden beam with a steel beam, we then replaced 25 wooden posts with SmartJacks. These will not rot or mold, and will re-stabilize the living spaces, eliminating the bounce that was occurring. The homeowner then wanted their 6 Mil vapor barrier replaced and a small upgrade. So we installed a drainage system, TripleSafe sump pump, and a new 6 Mil vapor barrier. 

This home would experience pools of water around their home in their yard when the rains hit. For a while that was all it was, but this water was now appearing in their basement as well. Water had made its way in and the homeowners were doing their best with fans, but each year it was getting worse. They called up John's Waterproofing to schedule their free inspection and see how we could solve their water issue. 

To begin we dug a trench around the basements interior perimeter. Here we laid in a bed of gravel and our WaterGuard drainage system. This will provide a route for the water to follow to the lowest point where a TripleSafe sump pump steps in. This will send the water safely away from the homes foundation to a LawnScape outlet. The walls were then covered in BrightWall paneling, ensuring any water from the homes foundation is guided to the WaterGuard to be dealt with. We then installed a SaniDry dehumidifier to address moisture in the air. Now the basement can remain dry and healthy. 

This home had storage shelving around the basement, and a musty odor had begun to seep into the space. The owners looked under the shelving and saw water coming in where the foundation wall met the floor. They called up John's Waterproofing and scheduled their free inspection with John's Waterproofing to see how we could solve the homes water issue. 

Our crew started by digging a trench around the interior perimeter of the basement. Here we laid in gravel and our WaterGuard drain system. This provides a path for water to follow to the lowest point where a TripleSafe sump pump will then send the water safely away from the homes foundation. We then installed BrightWall panels on the foundation, allowing all moisture from the walls to safely be guided to the new drain system. A SaniDry dehumidifier was installed to keep the moisture in this space controlled. Now the homeowner can put back their shelving and rest assured their basement will remain dry and healthy moving forward. 

Damp Odors were in the basement and wafting up into the living spaces. The homeowner was bothered by this and worried about what it would mean for their breathable air quality. So they scheduled their free inspection with John's Waterproofing so they could talk over options and get a solution built out to address their needs. 
To begin we dug a trench around the homes interior perimeter. Here we poured a layer of gravel and installed our WaterGuard drain system. This system will collect water from the foundation walls as well as collect it from the ground, and allow it to travel to the lowest point. From here it goes into the TripleSafe sump pump to be directed away from the homes foundation to a LawnScape outlet. To ensure water is guided safely down the walls we installed our CleanSpace wall system, which is a 20 Mil vapor barrier with a woven fiber through it to help it last over the years. To finish off this job we then installed a SaniDry dehumidifier to ensure the space has healthy air. 

When the driveway is sloped to the garage, this can cause some water issues. This home had water that was running down the driveway and when heavy rains occurred, water would puddle and enter the garage space. One option for them would be to have the driveway redone, including a better slope to allow water to travel off and away, but the homeowners were looking for something more affordable, and that wouldn't leave water pooling in the flower beds around their driveway too. They had John's Waterproofing out and we helped create a repair plan for this home. We dug a trench along the exterior of the garage door. Here we installed our TrenchDrain system. This will collect any water coming down the driveway. This connects to a drain system that is then buried through the yard to carry the water safely away from the homes foundation, and away from the homeowners landscaping to a LawnScape outlet. The homeowners are pleased with how the system looks so nice and happy to know the heavy rains won't bring an added stress for them. 

This home would accumulate inches of water when the rains came along. They had a 6 Mil vapor barrier, but this just had the water rise up over it, and stand stagnant until it could drain again. The owners knew this wasn't healthy for their home, so they called up John's Waterproofing. After a full inspection, the system design specialist sat down with the homeowner and went over options, crafting a repair plan for them. 

To begin we pulled out the old mud-encased vapor barrier and general debris. There was strips of old fiberglass still present, these were pulled out as well. We then installed a full interior drain system in a silt sock. This will collect the groundwater and allow it to travel to the lowest point of the space. Here an UltraSump Plus with a battery back up was installed. This will pump the water safely away from the homes foundation. The homeowners experience semi-frequent power outages, so the battery back up was high on their priority list. We then laid down a new 6 Mil vapor barrier, overlapping the edges and running it up the walls. This will help it stay in place so it can last longer. 

Moisture on the wall, this is what the homeowners began to notice. The owners began to get nervous about what this would be doing for their health. So they called up John's Waterproofing to learn about what they can do for their home so this moisture wouldn't cause long-term issues or worsen. 

To begin on the work we dug a trench around the homes interior perimeter. We laid a bed of gravel in this with our WaterGuard drainage system over it. This will be fed water from the walls and collect the groundwater. It then acts as a direct route for this to travel to the lowest point where a TripleSafe sump pump will pump the water safely away from the homes foundation. On the walls we installed our BrightWall paneling, this provides a semi-finished look for the space and safely allows any wall moisture to be guided to the below drainage system. We then installed a SaniDry dehumidifier which will address the moisture issues in the air to the environment will be healthier. The homeowner is happy to know their home is healthier and noticed the space smells fresher already. 

This homeowner wanted to have their old vapor barrier replaced. They knew it was suffering from being chewed on, and they had a critter issue. The space smelled bad and it was wafting up into their living spaces. Looking for an encapsulation, they called upon John's Waterproofing. We did a full inspection and went over their options, crafting a solution to fit their needs. 

To begin we removed the old vapor barrier and general debris. We then sealed shut the spaces vents. A full interior drain system was then installed, this will ensure water can travel, uninhibited, to the lowest point of the crawl space, where a new UltraSump Plus pump will sent the water away from the homes foundation. TerraBlock insulation was then laid over the dirt, and CleanSpace installed over this. CleanSpace has a woven fiber through it which deters critters from chewing it, and has a 25 year warranty against rips and tears. Spray Foam is applied to the foundation walls to insulate and air seal, and we finished by installing a SaniDry dehumidifier. The homeowner is so happy with how clean and bright the space is and is happy to note that is smells way better already. 

When searching online this homeowner read up about encapsulation. After doing their research they knew they wanted to protect their home against water damage year after year, and that meant finding the company that could do encapsulation the right way. So they decided to call up John's Waterproofing. To begin, before arriving we sent them a book about crawl space science. They were impressed by this sharing of knowledge and looked forward to getting to discuss the process more thoroughly with their design specialist. In the end they moved forward with out encapsulation for a few key reasons. Firstly the warranties on the products, secondly, the warranties on the installation, and lastly because we had science on why our system works. They enjoyed learn about why our vapor barrier has to go under the wooden post, not just taped around it. They knew that, that kind of attention to detail would help their crawl space remain dry. 

So we pulled out the old vapor barrier, old insulation, and the general debris that had accumulated here. We then installed a full interior drain system with an UltraSump Plus. These will work together to ensure any groundwater will safely be pumped away from the home. We then sealed the vents shut, and began to encapsulate. We did this with TerraBlock insulation along the dirt floor and SilverGlo along the foundation walls. We then brought in CleanSpace, this goes under each wooden post, anchors along the foundation rim joist, and seals along each seam with our four inch wide waterproof tape. We then installed a SaniDry dehumidifier which will address humidity issues in the air. The homeowners feel much better knowing that their crawl space is set up for success. 

This homeowner was concerned about their health. While they didn't seem to have water in their crawl space, they knew it could use some work. It was a mess under the home, from dusty debris, critter droppings, and fiberglass hanging from the sub-floors. They could smell space while in their living spaces and were ready for a change. We went out and performed a full inspection, and then went over options, landing on a full encapsulation to ensure the space could be healthier all year round.

To begin we cleared the space of the old vapor barrier, insulation, and debris. We then installed a SmartSump as a back up for any odd weather. Where they were situated, water wasn't an issue for them. We then sealed the vents shut and upgraded the exterior entryway, going from a metal well with plywood over it to a Turtl entryway that can be safely sealed shut to keep critters out. TerraBlock insulation was then laid over the dirt floor, and SilverGlo insulation was installed along the foundation walls. CleanSpace came in next, going under each wooden post, anchored to the walls, and sealed along each seam. We finished by installing a SaniDry dehumidifier and air sealing the space. The homes crawl space is much cleaner and healthier now, the owners already are excited to be able to smell the difference. 

This homes basement was in need of some waterproofing. There were water stains dripping down the foundation walls and small pools of water would formulate along the basement floor. To get the space cared for, the owners of the home called up John's Waterproofing and scheduled their free inspection. During this inspection we did a full walk through of the basement and then sat with the owners to discuss options, answer questions, and craft a repair plan that fit the home. 

To begin we dug trench around the basements interior perimeter. We laid gravel in this with our WaterGuard drain system over it. This will ensure water is collected, and it can safely travel to the lowest point. From here it enters a newly installed TripleSafe sump pump which sends the water safely away from the homes foundation. Along the walls we then installed our CleanSpace Wall systems which ensures moisture from the walls can safely travel to the drainage system to be dealt with as well. This material will not mold or rot. We then installed a SaniDry dehumidifier in the basement to ensure the spaces moisture content stays within a healthy range. The space is now ready to remain dry and healthy year after year. 

This homeowner experienced water flooding in their basement. This is a huge issue because they live in an area with heavy rainfall. If the water continued to flood every time it rained, it could cause serious water damage to the home and promote mold growth. In order to solve this issue, they contacted John's Waterproofing about their options. We discussed the problem and offered a solution to waterproof their basement so that the water could no longer overfill and flood the space. 

To begin waterproofing the basement, we installed a WaterGuard drainage system. This is installed along the interior perimeter of the basement and collects water to send to the TripleSafe sump pump. This sump pump is designed to safely send water away from the homes foundation and protect against standing water. In order to protect the exterior of their home from the heavy rainfall, we even connected the gutter to the rain drain so that their landscaping wouldn't be destroyed from flooding outside. These all work to waterproof the basement by offering a safe passage for water to flow through when it does rain and keeping it from flooding.

This homeowner reached out to John's Waterproofing after discovering their crawl space wasn't in good condition. They wanted information on how they could protect their home all while staying within a budget. At John's Waterproofing we like to give homeowners options on how they can protect their homes against moisture and what they feel comfortable with. We suggested that a Pipe Pump Plastic method would best benefit their crawl space if they didn't want to fully commit to an encapsulation yet. They thought it was the perfect solution that way drainage could be installed and could start protecting their home against water.

The Pipe Pump Plastic method begins by installing drainage along the interior perimeter of the crawl space. We dig a trench and lay a perforated pipe in a silt sock. This pipe acts as a safe passageway to guide water out of the crawl space and prevent any flooding. This pipe connects to our TripleSafe sump pump. This three-pump system is capable of collecting gallons of water and safely pushes it out and away from the homes foundation. It is able to run constantly and independently so that the homeowner doesn't have to worry about it at all. After the drainage system is installed, now we need to add a layer of protection against moisture from seeping up into the crawl space. This is why we install a 6 mil vapor barrier along the base of the crawl space. It is also anchored up the foundation walls to guide moisture from the walls down to the drainage system to be pushed away from the home. Once this process is completed, the crawl space now has a system set up to protect against groundwater and prevent flooding. 

This homeowner started noticing strange smells in their home and couldn't find the source of the issue. After inspecting their entire house and finding nothing that could've been the root to the smell, the only thing left to check was the crawl space. Because they didn't feel comfortable going into the crawl space themselves and seeing if there was an issue, they reached out to John's Waterproofing. We discovered that mold had grown all throughout the crawl space and was causing the smell that seeped into the air in the living spaces. The homeowner wanted a solution that would prevent future mold growth and agreed to an encapsulation.

The purpose of an encapsulation is to be able to control the environment in the crawl space that helps avoid mold. Mold can only grow if there is high humidity levels and humidity varies depending on how much moisture is in the air. This happens when water gets into the crawl space, evaporates, and without proper control of the environment it will raise the humidity. The first step of the encapsulation process is removing any damaged insulation and vapor barrier that moisture had caused to deteriorate. We then apply a mold spot treatment; MoldX, to the places where there is growth. Then, we install a drainage system to prevent standing water. This drainage system includes installing a perforated pipe along the interior perimeter of the crawl space and connecting it to a TripleSafe sump pump. The sump pump is capable of collecting that water and pushing it out away from the homes foundation. With a safe passageway for water to go through, then we can install insulation. TerraBlock is a 3/4 in. thick foam that is fit to each crawl space and creates a vapor barrier for the floor. A CleanSpace vapor barrier is installed over top of the TerraBlock that prevents water from coming into the crawl space. It is also installed between the concrete footing and wooden posts to isolate and protect the wood from getting water damaged. Finally, SilverGlo is applied to the foundation walls to insulate and air seal and a SaniDry dehumidifier is installed. Once this encapsulation is completed, it can control the crawl space's environment to prevent mold growth and stop any strange smells.  

This homeowner hadn't checked their crawl space in a long time and was curious what was going on underneath their home. They decided to reach out to John's Waterproofing to get a free inspection just to see if there was anything it needed to help maintain a healthy home. After our inspection, it was discovered that there crawl space had lots of water puddling and was in need of new insulation. We informed them that if the crawl space was left in this condition it could increase exposure to mold, rotting wood, and impact the air quality in their home. They agreed that a full encapsulation would be the best option to maintain a healthy living space. 

Encapsulations are a key part in maintaining the health of the home and its occupants. By encapsulating, it removes any moisture filling the crawl space and improves the air quality. According to the Stack Effect, any air that leaves your home through the attic must be replaced, and that comes from the air in the crawl space. If your crawl space is in bad condition with mold growth and high humidity, then you could be breathing in those harsh toxins. When we begin an encapsulation, we first need to take out the vapor barrier and insulation due to them being water damaged. Then, we install a drainage system using a perforated pipe. This pipe is installed along the interior perimeter of the crawl space to collect water and provide a safe passageway to flow through. The perforated pipe connects to a TripleSafe sump pump which takes all that water and pushes it out away from the homes foundation. After a drainage system is completed, we install the TerraBlock insulation foam. This thick, durable foam is designed to improve energy efficiency in the home by insulating the crawl space floor. We then install a CleanSpace vapor barrier that is a 20 mil thick which seals the crawl space floor and adds moisture protection. Spray foam is applied to the foundation walls that expands to fit every crack or crevice to completely air seal the space. Finally, a SaniDry dehumidifier is installed and pulls moisture out of the air, controlling the environment. Once the encapsulation is completed, the homeowner can enjoy living in a home with high quality air.

Water in the crawl space is never a good sign. This homeowner had to experience that the hard way after discovering puddles of water filling their crawl space. Immediately unsure what to do, they contacted John's Waterproofing about their options of getting the water out. We suggested a full encapsulation as the best option to provide a long-term solution to stopping water from getting into the crawl space and risking structural damage.

When we do an encapsulation the first thing we need to do is ensure we can install a drainage system. Drainage of one of the most important steps in an encapsulation process because it provides a safe passageway for water to flow through and be pushed away from the homes foundation. We do this by digging a trench around the interior perimeter of the crawl space and laying a perforated pipe in it. This pipe has holes in it to collect water and, through gravity, can direct it to the sump pump. The TripleSafe sump pump is connected to this pipe and it is a three-pump system that can push water away from the homes foundation. Then we install a insulation foam. TerraBlock is a 3/4 in. thick foam that is puncture-resistant. It is designed to help control the environment and insulate. A CleanSpace vapor barrier is installed on top of the TerraBlock and between the concrete footing and wooden posts. This is to isolate the wooden posts and protect them from getting water damaged. To air seal and insulate, Spray Foam is applied along the foundation walls. Lastly, a SaniDry dehumidifier is installed that works to pull moisture out of the air and control the atmosphere. Once the encapsulation process is completed, then the homeowner no longer has to worry about water getting into their crawl space and causing structural damage to their home.

Water in the basement is never a good sign. Being able to identify where the water is coming from is important in knowing what to do next and ensure that it doesn't happen again. Thankfully, this homeowner noticed the water seeping into the basement and immediately called John's Waterproofing about how to solve this issue. Upon inspection, we discovered that the water was leaking in because there was no yard drainage. Therefore, every time it rained and puddled in the yard it was then seeping down into the foundation of the basement. Since the foundation is made of a porous material, as water pressure pushes against it, it slowly makes a path through the foundation and seeps into the basement. We suggested installing a drainage system that would keep the basement dry and save the yard. 

For the drainage system, we install WaterGuard drainage pipe. WaterGuard is designed specifically to be a long-lasting drainage pipe that can guide water to a TripleSafe sump pump to be pushed away from the homes foundation. It has a 3/8 in. gap between the floor and the wall to drain wall leaks. It is also designed not to clog by sitting on top of the footing instead of alongside it to keep from wet dirt getting into the drain. To help the passage, it is lined with gravel to filter the water coming in. Overall, this heavy duty drainage pipe is the ideal method when installing a drainage system to keep water from puddling into the basement. Along the walls we then installed our BrightWall paneling, which provides a semi-finished look for the space. It is easy to clean, and safely allows water to travel down the walls into the WaterGuard. We then installed a SaniDry dehumidifier which will ensure the moisture content in the air is kept at a healthy level so mold and mildew cant grow here. Now this basement is set up to remain dry, stable, and healthy. 

This homeowner was experiencing water coming into their crawl space and didn't know where to begin to fix this issue. They decided it was best for a professional to come in and called John's Waterproofing. Upon inspection, it was discovered that water had been seeping into the crawl space for a long time. We suggested that a full encapsulation would be able to stop the water from seeping through and promote a healthy living space for the homeowner.

The first necessary step in an encapsulation is removing the falling fiberglass insulation and damaged vapor barrier. Then, we can install a drainage system using a perforated pipe that safely collects water and gives it a passageway to the TripleSafe sump pump. This sump pump takes all that water and sends it safely away from the homes foundation. It is a three-pump system that is installed at the lowest point in the crawl space. Next, we install TerraBlock insulation. This is a durable and thick foam designed to help control the environment by sealing the home off from the earth. It helps promote energy efficiency by helping to keep the outside air from getting into the crawl space so your heating/cooling systems don't have to work as hard to keep up with temperature changes. Then, we install the CleanSpace vapor barrier. This goes over top the TerraBlock, up the foundation walls, and between the concrete footing and wooden posts. It's primary function is to keep water out and is sealed in place with thick waterproof tape. A SaniDry dehumidifier gets installed to help filter the air and pull out moisture particles that can get into the living space. Finally, Spray Foam is applied along the foundation walls as a final insulation and air sealant. Now, the crawl space is protected from water seeping through and the homeowner can enjoy the benefits of a dry crawl space.

This homeowner wanted to get their crawl space inspected after not going down there in a long time. Upon inspection, it was discovered that there was significant water damage occurring in the crawl space, causing damage the wooden posts supporting the home. They asked what could be done to fix this issue and we suggested a full encapsulation along with installing SmartJacks.

To begin the full encapsulation process, we first need to install a drainage system. Drainage is important so that there is a safe passageway for water to flow through and be pushed away from the homes foundation. It helps to protect against standing water or moisture damage if that water evaporates and gets into the air. We dig a trench along the interior perimeter of the crawl space and lay a perforated pipe. This pipe then connects to a TripleSafe sump pump. The sump pump takes all that water and is able to push it out of the crawl space and away from the homes foundation through a discharge line. After a drainage system is installed, then we can start installing an insulation foam. The thick 3/4 in. insulation foam, TerraBlock, is installed along the base of the crawl space. This is a moisture barrier that separates the earth from the home and closes the crawl space off. Over top of the TerraBlock we install a new CleanSpace vapor barrier. This vapor barrier is stronger than code regulated ones because it is made of 20 mil thick woven fibers and is backed by a 25 year warranty against rips and tears. It is installed along the base, up the foundation walls, and between the footing and wooden posts. Next, we install a SaniDry dehumidifier that controls the environment by pulling any moisture out of the air. Finally, Spray Foam is applied to the foundation walls to insulate and air seal. This is the completed encapsulation process so no more water can have access into the crawl space and it is closed off from the outside air. In order to fix the damage done to the wooden posts, we install SmartJacks. These are adjustable steel piers that stabilizes the home in places where the previous posts have rotted. Now the homeowner can enjoy a dry and healthy crawl space that will support their home.

For some homeowners, it can be intimidating discovering that there is water in your crawl space and all the steps needed in order to solve the issue. Fortunately, at John's Waterproofing we try to accommodate every homeowner's situations and offer different options. In this circumstance, this homeowner had no idea that water had been seeping into their crawl space for a long time and had damaged numerous wooden posts and support beams that were under their home. They weren't expecting this outcome and wanted a solution just for the rotten wooden posts so that their home wouldn't begin the settling process. We informed them that installing SmartJacks could help with stabilizing their home until they were ready for a waterproofing system. 

Because wood is made of organic materials, it makes it the perfect surface to absorb water. Except, it is a bad, when this happens water breaks down the materials and causes the wood to rot and mold. Once the water has already been absorbed, there isn't a lot that can be done to repair the damage. Instead, at John's Waterproofing we install SmartJacks. These are steel adjustable piers that connect to the homes support beams to stabilize the home. They are made of materials that won't rot or mold so they can withstand any environment. This crawl space needed 14 SmartJacks and over 154 feet of support beams in order to give the home the support it needed due to the extreme water damage. Now, the homeowner can feel safe and comfortable in their home knowing it is properly supported until they are ready to resolve the water issue.  

This homeowner found that they didn't have a vapor barrier in their crawl space and were curious if that would begin to cause damage to their home. They didn't find any water in their crawl space, but did find that the entrance was completely open and exposed to the outdoors. Wanting to get an inspection and see what the benefits of closing their crawl space would be, they reached out to John's Waterproofing.

Ensuring your crawl space is protected from the outdoor elements is important in maintaining your home's health. By having an open entryway, this was allowing things to get into your crawl space that shouldn't be there. It imposes higher risks of rodent activity, humidity, and rotten wooden posts. Humidity is the amount of moisture in the air. This is what creates an atmosphere for mold and mildew to grow and wood to rot. To help address this issue, we install Turtl crawl space doors. This is an entry system with an airtight lid so that nothing can get into the crawl space that shouldn't be there. Homeowners also feel more secure because it can lock to prevent unwanted entry. Additionally, while the Turtl helps keep things out of the crawl space, an encapsulation is what protects what is inside. This stops moisture and water from seeping through and protects against water damage. Overall, this homeowner learned the benefits of closing their crawl space off in order to keep the structural integrity of their home strong.

This homeowner started noticing strange smells in their home. After cleaning their entire space, still unable to find the root of the murky odor, they decided it was time to check underneath their home. They reached out to John's Waterproofing and explained their situation with the bad smells with no source. After our inspection, we discovered that their crawl space had been infested with mold in their fiberglass insulation due to extreme moisture issues. 

Mold is a bacteria that grows on organic materials. But, in order for it to grow, it needs to be in a certain environment. When a crawl space has water issues, eventually that water evaporates into the air. After it evaporates, that raises the moisture levels in the air causing an increase in relative humidity. Thus, it creates a perfect environment for mold and mildew to grow. Without getting the moisture issue solved, this mold continues to spread and eventually eats away at the materials your home is made out of. Things like wooden posts and fiberglass insulation are typically the first surfaces that mold grows on and spreads before getting into your house. To solve this problem, we would go in with a spot treatment called MoldX. This is capable of prohibiting the mold to continue to spread. Then, we would remove all falling fiberglass insulation because it is no longer serving its purpose of properly insulating the home once it absorbs moisture and falls from the sub-floor. Afterwards, we installed a full encapsulation system. This is designed to control the environment under the home, making it a space where mold cannot grow. Once this process is completed, the home was rid of its murky odor and space was protected against any moisture issues from taking hold in the future. 

This homeowner started noticing that mold was growing in their garage and they couldn't figure out why. They inspected their entire home and found no source of water or moisture damage that would create an environment for mold to grow. Unsure of what else to do, they decided it was time to check underneath their home and called John's Waterproofing. It was discovered that their crawl space had a lot of moisture damage due to years of water flowing in and evaporating into the air. This is what was creating the environment for the mold to grow and eventually spread to the garage. We suggested doing a Pipe Pump Plastic method in their crawl space to help with water intrusion and stop any standing water based issues.

To begin, we first needed to remove the damaged insulation and vapor barrier that had years worth of water damaged absorbed into them. Then, we installed a proper drainage system so in the future, if water tries to enter there will be a safe passageway for it to flow through and exit the crawl space. For drainage, we install a perforated pipe along the interior perimeter of the crawl space and connected it to a SuperSump Plus sump pump. These two can work together to collect water and safely push it out and away from the homes foundation through a discharge line. After, we install a new 6 mil vapor barrier. This liner goes along the base of the crawl space, up the foundation walls, and between the footing and wooden posts. It is overlapped at each seam to prevent groundwater from being able to seep over top of it. For this home, because the moisture damage was so severe, we also installed a SaniDry dehumidifier to pull moisture out of the air. Once all this was installed, the homeowner doesn't have to worry about more mold being able to grow in their crawl space and can enjoy the benefits of a dry home.

Having a basement in your home helps to add hundreds of footage of usable space. But, it is only usable if it can stay dry during every season. This homeowner was beyond excited to have a basement and add to their home. Unfortunately, their basement had no waterproofing systems installed and would constantly flood during the heavy rainy seasons. Unsure of what to do, they decided to call John's Waterproofing and see what their options were. We informed them of our basement waterproofing system and how it works to keep that unwanted water out.

When waterproofing the basement one of the most important steps is installing a drainage system. We can't control how much it rains, but we can control where that rainwater goes with WaterGuard. WaterGuard is a drainage pipe that goes along the interior perimeter of the basement. It is placed at the footing and lined with gravel to help filter water through and avoid clogging. The drainage pipe acts as a safe passageway to collect water and guide it to a sump pump. It is designed to be able to collect any rising groundwater or water that tries to seep in through the walls. The SuperSump Plus sump pump is what takes the collected water from the WaterGuard and can push it out of the basement and away from the homes foundation. It is made with heavy duty Zoeller pumps to handle mass amounts of water. After the drainage system is installed, we then applied BrightWall to the basement walls. BrightWall is a white paneling that provides a semi-finished look and helps guide any water intrusion down below to the drainage system. It is made of materials that won't rot or grow mold to ensure a long-term solution to keeping water out of the basement. Now, the homeowner can enjoy all that usable space they were excited for without the threat of water ruining their things.

Understanding humidity is essential in keeping your home healthy. If the humidity levels in the crawl space get too high this can allow for exposure to mold and mildew or rotting wood. This homeowner did a test in their crawl space and found that their humidity levels were at 78%, which is dangerously high. A healthy crawl space should only have their humidity levels between 45%-55%. Knowing that this would cause long-term problems, the homeowner decided to call John's Waterproofing to find a solution.

Full encapsulations are designed to prevent mold and mildew growth because they regulate the relative humidity levels in a crawl space. Humidity refers to how full of water the air is. When to high, this creates condensation that gets absorbed by the materials in your house like the fiberglass insulation and the wooden posts. Once absorbed, it can cause mold to grow and even deteriorate the wooden posts to the point they can no longer support the home. When we encapsulate, first we remove all the damaged insulation and vapor barrier so we have a clean start. Then, we install a drainage system using a perforated pipe and a TripleSafe sump pump. These two work together along the interior perimeter of the crawl space to collect water and offer a safe passage to be pushed out. This helps keep the crawl space dry so water can't intrude and eventually evaporate into the air. Next, we install TerraBlock insulation foam along the base of the crawl space which seals the earth off from the home and helps to regulate the environment. A CleanSpace vapor barrier goes on top of the TerraBlock, up the foundation walls, and between the footing and wooden posts to isolate and protect from water seeping over top of it. Spray Foam is applied to the foundation walls as a final air sealant and insulator. Lastly, we install a SaniDry dehumidifier to ensure all the excess moisture or particles in the air is pulled out so that the humidity is controlled and the air is clean. After this process is completed, the humidity levels in the crawl space can be regulated.

Making improvements to your home will not only benefit your homes overall health, but its occupants' too. This homeowner was worried about the negative health effects that water in the basement can cause to the people living there. They decided they wanted a professional to come take a look at their basement and reached out to John's Waterproofing. We informed them that water in the home is never a good sign and can lead to things like mold and mildew growing. These are toxic to breathe in and can impact the air quality of the home. We recommended getting a basement waterproof system installed so that water won't be able to continue seeping through into the home to preserve the homes health and benefit the homeowner's too.

When we do a basement waterproof system, the most important step is installing a proper drainage system. We jackhammer a trench along the interior perimeter of the basement so we can install a WaterGuard drainage pipe. WaterGuard sits alongside the footing of the basement and is lined with gravel so that it can easily collect any water that tries to seep in. It acts as a safe passageway so rather than water just leaking into the basement, it now has a direction to flow and be sent out of the basement. We can ensure this because the WaterGuard connects to a TripleSafe sump pump. This three pump system is capable of controlling large volumes of water and can safely push it out of the basement and away from the homes foundation through a discharge line. While this drainage system controls the inflow of water and getting it sent out, we also want to make sure the basement walls are protected. We do this by installing a CleanSpace wall vapor barrier. This thick liner is made with woven fibers that protect against rips or tears to guide water down below to the drainage system. This way, wherever water tries to enter it will be redirected to the TripleSafe to be sent away from the home. To address excess moisture within the air we then installed a SaniDry dehumidifier in the basement and an Aspen air purifier in the living spaces. Once the basement waterproofing system is fully installed, this homeowner gets to enjoy all the health benefits that come with owning a dry and healthy basement.

This homeowner had water constantly leaking through their basement walls every time there was heavy rain. Wanting to find a long-term solution to keeping the water out all year, they reached out to John's Waterproofing. We suggested getting a basement waterproofing system installed so that the basement would be able to stay dry and healthy no matter what season it was. 

Basement waterproofing is the process of installing a drainage system and a wall vapor barrier so that any water that tries to enter can be redirected and sent out of the basement. But how can we do this? The first step is installing a drainage system using a WaterGuard drainage pipe. This is installed along the interior perimeter of the basement and acts as a safe passageway for water to flow through. It collects any water from the ground or from the walls and sends it to a TripleSafe sump pump. This three pump system is what actually takes all the collected water and pushes it out of the basement and away from the homes foundation. Each pump is placed at a higher position so that large volumes of water can be pushed out at a time. It also has a backup battery operated pump in the case of a power outage, so no matter what the basement will stay dry. After the drainage system is installed and there is control over the flow of water, then we install a wall system. Because this home deals with a lot of heavy rain, we installed a CleanSpace wall vapor barrier along the basement walls. This is a 20 mil thick liner made with woven fibers that help prevent any rips or tears. It is so durable that it is backed by a 25 year warranty against rips and tears. This keeps water from being able to seep through and just acts as a guide for any water or moisture to be sent down below to the drainage system. After this entire basement waterproof system is installed, the homeowner now has a long-term solution, preventing water from getting into their basement.

As homeowners, the goal is to keep your home running smoothly and staying healthy. But sometimes you don't know there's a problem until it's too late. That was the case for this homeowner who started noticing strange smells in their home and couldn't find the root of the problem. They inspected everywhere and found that it had to be coming from beneath their home. They reached out to John's Waterproofing for a solution to save their home and get rid of the smell.

Upon inspection, we found that there had been significant water issues in the crawl space. When water enters the crawl space and evaporates into the air, this can cause high humidity levels and bad smells in the living spaces. The best long-term solution to these kind of water issues away is to encapsulate. When we encapsulate, the first thing is to remove all the debris in the crawl space. Things like a damaged vapor barrier, falling insulation, and rodent droppings are all factors that contribute to bad smells in the home. Then, we install a drainage system so that any water that tries to enter has a safe passageway to exit the crawl space. A SuperSump Plus sump pump is designed to take all the collected water from the drainage system and safely push it out and away from the homes foundation. For better insulation, we install TerraBlock along the base of the space. This is a thick insulation foam that seals the earth off from the home and helps to improve energy efficiency. To ensure water has no access inside again, we install a CleanSpace vapor barrier along the base, up the foundation walls, and between the footing and wooden posts. This is a 20 mil thick liner made with woven fibers that prevent water from being able to seep through. A SaniDry dehumidifier gets installed to filter the air and pull out any excess moisture. The final step is to apply Spray Foam to the foundation walls. This is a strong insulator and air sealer that expands to fit every crevice on the foundation walls. Once this entire process is completed, the homeowner will get to enjoy a smell-free home and a dry crawl space.

After seeing an advertisement online about nasty crawl spaces, this homeowner was curious about the state of their own crawl space. They went down only to find the worst case scenario. Fiberglass insulation was falling from the sub-floor, signs of water damage on the wooden posts, and even rodent droppings covering the base. Knowing that this was a huge problem for their homes health, they decided to call John's Waterproofing and get the situation resolved. 

At John's Waterproofing, we are able to clean up and encapsulate crawl spaces so that they can stay dry and healthy year round. When beginning this process, we go in and remove all the debris and falling insulation. This creates a clean space so we can install a drainage system. Most of the time crawl spaces get in these bad conditions because there is water issues that eventually evaporate into the air and causes humidity. By installing a drainage system, we can control the water that tries to enter the crawl space and offer it a safe passageway to exit. This is done using a perforated pipe that collects the water and sends it to a SuperSump Plus sump pump. The sump pump pushes that collected water out of the space and away from the homes foundation to keep it dry. Then, we install TerraBlock insulation foam along the base of the crawl space to seal the earth off from the home and promote better energy efficiency. To prevent any future water from seeping through, a CleanSpace vapor barrier gets installed along the base, up the foundation walls, and between the footing and wooden posts. Because we are completely sealing the space, a SaniDry dehumidifier gets installed to filter the air and pull out any moisture. The last step is to apply Spray Foam to the foundation walls as a final air sealant and insulator. Now, this homeowner can enjoy all the benefits of a dry crawl space and a healthy home.

This homeowner had an area in their basement that would always flood with water. Tired of having to clean up the damp messes, they were open to getting help and they decided to call John's Waterproofing about a solution. We schedule their free inspection and they had water seeping in through the cracks in the foundation and a basement waterproofing system would be able to prevent it from continuing.

Basement waterproofing involves installing a proper drainage system to collect water as it enters and offers a safe passageway to flow through. This is done by installing the WaterGuard drainage pipe. A trench gets jackhammered along the interior perimeter of the basement. Once the trench is dug and cleared out, the WaterGuard pipe can be placed into it. This allows for the pipe to sit at the footing of the basement and is lined with gravel for easy filtration. Once installed, WaterGuard is capable of collecting water from the walls or rising groundwater and send it to a SuperSump Plus sump pump. This pump then takes all the water intrusion and securely pushes it out of the basement and away from the homes foundation. With these two working together to constantly pump water out, then the basement is able to remain dry. We then installed our CleanSpace wall system to guide moisture from the walls to the WaterGuard and a SaniDry dehumidifier. Afterwards, the homeowner feels a lot safer knowing their basement will be able to survive another rainy season. 

Having proper insulation is incredibly important for every household. Not only does it help to prevent heat loss, but it is crucial for your homes overall health. Insulation can come in many forms, but the most commonly used is fiberglass. Fiberglass insulation is the foam padding attached to the sub-floor. Unfortunately, this type of insulation is not made for the crawl space and is the most prone to mold and mildew exposure. Any kind of water intrusion will result in the insulation absorbing the moisture and completely detaching from the sub-floor. So what are the other options?

Luckily, at John's Waterproofing our encapsulations are designed to seal the crawl space off and prevent future water intrusion. They involve the process of installing two different kinds of insulation to replace the damaged fiberglass. First, TerraBlock is a 3/4 inch thick insulation foam that is installed along the base of the space. It is cut to perfectly fit each individual crawl space and seal the home off from the earth. By sealing the earth off, this helps control the environment and maintain a consistent temperature year round. As a result, this helps improve the homes energy efficiency because the heating/cooling systems won't have to work as hard to keep up with the changing outdoor climate. The other type of insulation used is Spray Foam. This is applied to the foundation walls and is made of materials that expand to fit into each crack and crevice along the walls. This helps to fully air seal the crawl space and insulate the home. Once the encapsulation is completed with these two new types of insulation, the home is better protected against water and moisture damage and can remain dry and healthy.

Keeping the crawl space dry and healthy is more important than most homeowners understand. Not only does it impact the air quality in the living spaces and prevent musty odors, but it also helps keep the structural integrity of the home strong. The wooden posts in the crawl space are what support the homes foundation. If there is water intrusion and it gets absorbed into those posts it can cause them to rot or mold. Thus, they can no longer stabilize the home and result in sagging floors and doors not shutting properly. This homeowner wanted to ensure that their crawl space was in good condition to protect the structural support of their home and called John's Waterproofing. 

Upon our inspection, we found areas in the crawl space that indicated water had seeped through. Not only was the original vapor barrier ripped and covered in debris, but the fiberglass insulation was falling from the sub-floor. This shows that water was seeping through bringing outside sediment, then evaporating into the air and getting absorbed into the insulation. We recommended that by encapsulating the crawl space we would be able to offer a long-term solution to keeping water out. An encapsulation is the process of sealing the home off from the earth and installing new drainage and insulation. These all work together to regulate the crawl space environment so that it can stay dry and healthy all year round. Without the help of a TripleSafe sump pump, a SaniDry dehumidifier, and a new CleanSpace vapor barrier this home would have been at risk of water damage. But with our encapsulation, the homeowner can rest knowing that the home is protected and can maintain its overall health.

This homeowner started noticing that their back patio was starting to sag due to water infiltrating between the patio and foundation wall. Unsure if this was more of a structural concern and the home was settling or a waterproofing issue, the homeowner reached out to John's Waterproofing for answers. Upon our inspection, it was discovered that the water that was seeping through the foundation wall was getting into the crawl space and causing major moisture issues. This was absorbing into the homes natural materials like wooden posts and beams. Over time as that water evaporates and absorbs in, that causes the wood supporting the homes foundation to rot or mold. It makes the home unsupported and can result in sagging floor. We recommended that an encapsulation on the crawl space would help to stop the water from seeping through and provide a proper drainage system to be pumped away from the homes foundation.

To begin the encapsulation process, we needed to install a drainage system using a perforated pipe and a SmartDrain. These work together to collect water as it tries to intrude and offers a safe passageway to exit the crawl space. This helps prevent any kind of flooding and moisture issues because the water doesn't stay inside long enough to evaporate into the air. Next, TerraBlock is installed along the crawl space floor to seal the space off from the earth. This helps to regulate the environment and keep humidity levels low so that mold can't be exposed. A CleanSpace vapor barrier is installed on top of the TerraBlock, up the foundation walls, and between the footing and wooden posts. This is to isolate the space and protect against water damage. It is made with thick woven fibers that prevent water from being able to seep over top of it. Another important step is installing the SaniDry dehumidifier. This filters the air and pulls out excess moisture. The last part of the encapsulation process will be applying Spray Foam along the foundation walls to air seal and insulate. After this system is fully completed, the homeowner will be able to rest knowing there is control over the water intrusion and the wooden posts will now stay dry and healthy.